Compact 12 inch Bass Enclosure with Active Amplifier

Specifications

• 12″ Passive Subwoofer Enclosure
• 1500w Peak, 500w RMS
• Impedance: dual 2 ohm
• 13.8″ (351mm) x 15.8″ (402mm) x 11.4″ (290mm)
• 2nd order passive radiator enclosure
• 170w @ 4 ohm
• 1.5″ x 6.2″ x 3.2″ (37mm x 157mm x 82mm)
• 250w RMS @ 2 ohm
• 400w RMS @ 1 ohm
• Frequency response: 10Hz – 500Hz
• Crossover type: LP/subsonic
• Crossover range: 30Hz – 150Hz Class D micro amplifier

Enclosure Design

• Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
• Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
• Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
• Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
• High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
• Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
• Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Amplified Space Saver

A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.

Remote Subwoofer Control

A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS

• Full Range 4" 4-Way Speaker Pair
• 250 Watts MAX 125 Watts RMS Power Handling per Pair
• 120 Hz to 20 kHz Frequency Response and 90dB Sensitivity
• Poly Injection Woofer Cone and Rubber Surround
• 2 Tweeters and 1.18 inch Mylar Cone Midrange Per Speaker
• Sold in Pairs

PULSE12-V0 - 12 Inch Subwoofer

Low budget doesn’t have to mean low performance! The PULSE12 is part of the series of affordable subwoofers that deliver all of the brand values synonymous with VIBE.

The same wide roll foam surround technology found in our SLICK series subwoofers allows huge excursion and delivery of powerful bass, this paired with our custom tooled duscap for added rigidity and harmonised engineering or voice coil, spider, cone and magnet allows deep low frequencies and accurate bass reproduction.

High temperature single 4Ω voice coils deliver maximum flexibility with a wide range of amplifiers including bridged onto any of our multi-channel Powerbox amplifiers.

Specification

• 50 Watts x 4 Max Power, Balance/Fader/Bass/Treble and Preset built-in EQ
• Plays Bluetooth/CD, FM/AM, Digital Media from Smart Phones
• Compatible with Audio out from Smart Phones and MP3 Players
• Aux, Input
• Front & Rear Pre Amp Outputs
• Wireless Remote
• Bluetooth Hands Free, Make and receive cal

British Engineered 1 Inch Component Tweeter

The secret weapon is the incredible tweeter. The component tweeter uses high end components and is one of the smallest on the market, but packs a huge punch, causing Car & Hifi magazine to call it a force to be reckoned with as it provides great detail and good spatiality.

Specification