SLICKV12T-V2: Hybrid venting combines both slot and tube ports to deliver incredible low frequencies.
Lean and mean vented bass enclosure.
The all new SLICK V12 (SLICKV12T-V2) delivers all the performance you’ve come to expect from the SLICK CBR but in a slim form factor. Ideally suited to vehicles with small or shallow trunk space, the SLICK V12 is over 30% less deep than its bigger CBR sibling yet manages to match the performance. The SLICK V12 series are designed to offer maximum compatibility with a wide range of amplifiers thanks to their dual voice coils.
Specifications
Model: SLICKV12T-V2
Driver: 2 x SLICK12
Type: Passive bass enclosure
Peak Power: 2400 Watts
RMS Power: 800 Watts
Impedance: Dual 2 Ohms
Dimensions (H x W x D): 13.9″ x 35.4″ x 11.3″ (355mm x 900mm x 288mm)
Configuration: 4th order bass reflex
Enclosure Type: Trapezius Bass Enclosure
Recommended Amplifier: POWERBOX400.1M-V7
Reviews
There are no reviews yet.
Be the first to review “SLICKV12T-V2 – VIBE SLICK 12 Inch Twin Passive Bass Subwoofer Enclosure” Cancel reply
BlackDeath 10 Inch Pro Audio Midrange high output driver
Alloy Gasket included
Sold in Singles
BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
SLICKV12T-V2: Hybrid venting combines both slot and tube ports to deliver incredible low frequencies.
Lean and mean vented bass enclosure.
The all new SLICK V12 (SLICKV12T-V2) delivers all the performance you’ve come to expect from the SLICK CBR but in a slim form factor. Ideally suited to vehicles with small or shallow trunk space, the SLICK V12 is over 30% less deep than its bigger CBR sibling yet manages to match the performance. The SLICK V12 series are designed to offer maximum compatibility with a wide range of amplifiers thanks to their dual voice coils.
Specifications
Model: SLICKV12T-V2
Driver: 2 x SLICK12
Type: Passive bass enclosure
Peak Power: 2400 Watts
RMS Power: 800 Watts
Impedance: Dual 2 Ohms
Dimensions (H x W x D): 13.9″ x 35.4″ x 11.3″ (355mm x 900mm x 288mm)
Configuration: 4th order bass reflex
Enclosure Type: Trapezius Bass Enclosure
Recommended Amplifier: POWERBOX400.1M-V7
One 12" Woofer with DUAL 4 ohm Voice Coil
1600 Watts MAX 800 Watts RMS Power Handling
85dB Sensitivity, 26 Hz Resonant Frequency
Polypropylene & Paper Cone and Rubber Surround
Works in .65 CuFt Sealed or 1.5 CuFt Ported enclosure
Blue LED Illumination
Competition 10" pro audio speaker
The BDPRO10M-V9: BlackDeath 10 Inch Pro Audio Midrange woofer is designed with excellent mid-bass response in mind. A semi-pressed paper cone has high sensitivity and low moving mass for monstrous output. Dual roll cloth surround offers fast, precise dampening of the cone with great bass response. The BlackHole Dustcap increases the effective cone area for higher SPL creating extreme volume.
BlackDeath range
VIBE Audio’s BlackDeath range is all about taking things to the extreme and creating products so crazy they have no right to exist. BlackDeath isn’t just about pushing the boundaries of audio innovation, it’s about annihilating them.
For many years people have been asking for coaxial and component speakers that are worthy to wear the BlackDeath logo, and after extensive development Vibe are proud to release the BlackDeath Pro Audio range.
Derived from PA speaker design, BlackDeath Pro Audio speakers are capable of immense sound pressure levels, meaning volume like you’ve never heard before. Ideal for competition use or for those who just want to play their music loud and proud.
Specifications
Model : BlackDeath Pro 8M
Configuration : 1 Way
Speaker Size : 10″ (2254mm)
RMS Power : 275 watts
Peak Power : 825 watts
Minimum Input : 125 watts
Sensitivity : 97 dB
Freq. Response : 55 Hz – 3.5 kHz
Impedance : 4 Ohm
Mounting Depth : 4.2″ (106mm)
Mounting Diameter: 9.25″ (235mm)
BOSS Audio Systems BAB8 Amplified Car Subwoofer
Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
BDPRO4T-V0 - Compression Horn Driver
Introducing from VIBE the latest BDPRO4T-V0 – VIBE BlackDeath 4.5 inch Compression Horn Driver.
The horn driver differs from a traditional pro audio tweeter by using an inverted membrane at the back of the driver, this gives a longer loading into the throat of the horn. This design has been derived from the line array style horn drivers you would see at huge concerts and adapted to work in a car audio scenario.
The Aluminum horn is strategically shaped to allow extreme wideband playback from 1.5kHz to over 20kHz and with a very high sensitivity of 107dB! This means that the compression driver is one of the loudest on the market.
We developed the driver to have a wonderful wide response concentrating and ensuring linear playback across its bandwidth and ensuring no loss of output or sensitivity at the high end.
Be sure to pair this monster driver with any of our latest BlackDeath Pro mids for an incredible sound installation.
Specifications
Type – Compression driver
Configuration – 1-way
Speaker size – 4.5” (115mm)
Frequency Response – 1.5khz – 20Khz
Sensitivity – 107dB
RMS Power – 150 watts
Peak Power – 300 watts
Sensitivity – 105dB
Impedance – 8Ω
Mounting Depth – 2.6” (67mm)
Mounting Diameter – 3.5” (90mm)
pro audio compression driver
composite aluminium diaphragm
Torsion basket featuring snap on mounting tabs for greater installation flexibility.
cast aluminium housing
wide frequency response
high power y35 ferrite magnet
spring loaded terminals
Frequency Response
One 10" Woofer with DUAL 4 ohm Voice Coil
2100 Watts MAX 1050 Watts RMS Power Handling
88dB Sensitivity, 34 Hz Resonant Frequency
Poly Injection Cone and Rubber Surround
Works in .65 CuFt Sealed or 1 CuFt Ported enclosure
Reviews
There are no reviews yet.