| Description |
- SLICKV12T-V2: Unique Amplifier Docking System allows easy fitment of the Powerbox 400.1M.
- Ported enclosure delivers higher SPL and boosted bass response.
- Hybrid vent incorporating a slot port and flared turbo ports.
| Phantom - 10" DUAL Voice Coil (4 Ohm) 2100W Subwoofer. (Sold Single) | BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space |
- PULSE4-V0: Pulse 4 Inch Coaxial Speaker
- Easy upgrade
- Complete with grills
| The new range of Vibe Slick speakers are the most efficient Vibe speaker to date. | Onyx 5.25" 4-Way 300W Full Range Speakers. (Sold in Pairs) |
| Content | SLICKV12T-V2: Hybrid venting combines both slot and tube ports to deliver incredible low frequencies.
Lean and mean vented bass enclosure.
The all new SLICK V12 (SLICKV12T-V2) delivers all the performance you’ve come to expect from the SLICK CBR but in a slim form factor. Ideally suited to vehicles with small or shallow trunk space, the SLICK V12 is over 30% less deep than its bigger CBR sibling yet manages to match the performance. The SLICK V12 series are designed to offer maximum compatibility with a wide range of amplifiers thanks to their dual voice coils.
Specifications
- Model: SLICKV12T-V2
- Driver: 2 x SLICK12
- Type: Passive bass enclosure
- Peak Power: 2400 Watts
- RMS Power: 800 Watts
- Impedance: Dual 2 Ohms
- Dimensions (H x W x D): 13.9″ x 35.4″ x 11.3″ (355mm x 900mm x 288mm)
- Configuration: 4th order bass reflex
- Enclosure Type: Trapezius Bass Enclosure
- Recommended Amplifier: POWERBOX400.1M-V7
|
- One 10" Woofer with DUAL 4 ohm Voice Coil
- 2100 Watts MAX 1050 Watts RMS Power Handling
- 88dB Sensitivity, 34 Hz Resonant Frequency
- Poly Injection Cone and Rubber Surround
- Works in .65 CuFt Sealed or 1 CuFt Ported enclosure
|
BOSS Audio Systems BAB8 Amplified Car Subwoofer
- Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
- Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
- Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
- Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
- High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
- Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
- Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
| Entry level 4 inch Coaxial speaker with IMPP Cone
The PULSE4-V0: Pulse 4 Inch Coaxial Speaker are the new entry level range from Vibe. Designed to be extremely efficient to produce the best response possible without the need for an amplifier upgrade.
Specifications
- 4”(100mm) 2-way high efficiency coaxial speaker 120 Watt
- Peak Power output – 40 Watts
- RMS Frequency Response: 100HZ – 20KHZ
- Sensitivity 83dB
- Mounting Diameter 3.7” (95MM)
- Mounting Depth 1.7” (44MM)
- Impedance : 4 OHMS
- Spade Terminal allows easy connection of speaker Cable.
- PEI Tweeter – PEI dome tweeters deliver extended high frequency response.
- Torsion basket featuring snap on mounting tabs for greater installation flexibility.
- IMPP Woofer Cone – Rigid injection moulded polypropylene (IMPP) woofer cone delivers smooth, low bass and great vocal reproduction.
| British Engineered 1 Inch Component Tweeter
The secret weapon is the incredible tweeter. The component tweeter uses high end components and is one of the smallest on the market, but packs a huge punch, causing Car & Hifi magazine to call it a force to be reckoned with as it provides great detail and good spatiality.
Specification
- - 2″ Tweeter, 150w Peak
- - 50w RMS, 1 way
- - impedance 4 ohm
- - Sensitivity: 94dB
- - Frequency response: 1.5kHz – 25kHz
- - Mounting depth: 0.5″ (12mm)
- - mounting diameter: 1.5″ (39mm)
- - Grill included
|
- Full Range 5.25" 4-Way Speaker Pair
- 300 Watts MAX 150 Watts RMS Power Handling per Pair
- 95 Hz to 20 kHz Frequency Response and 90dB Sensitivity
- Poly Injection Woofer Cone and Rubber Surround
- 2 Tweeters and .98 inch Mylar Cone Midrange Per Speaker
- Sold in Pairs
|
Reviews
There are no reviews yet.