BOSS Audio Systems BAB8 Amplified Car Subwoofer – 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
Space Saver – The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier – A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated – This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter – A low-pass filter is an electronic circuit that removes all the notes below the filter’s frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input – Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input – Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost – Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
Reviews
There are no reviews yet.
Be the first to review “BOSS Audio Systems BAB8 Amplified Car Subwoofer” Cancel reply
BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
BOSS Audio Systems NX654 Car Speakers - 400 Watts Per Pair, 200 Watts Each, 6.5 Inch, Full Range, 4 Way, Sold in Pairs
Single-DIN, CD/MP3 Player Bluetooth
Content
BOSS Audio Systems BAB8 Amplified Car Subwoofer
Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
Break Your Subwoofer In
Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.
8-inch 800-Watt subwoofer
Class A/B built-in amplifier
MOSFET power supply
RCA & speaker level input
Phase control
Bass boost
Low pass filter
Remote subwoofer control
Amplified Space Saver
A built-in amplifier powers the 8-inch subwoofer. No need to have a subwoofer housed in a box AND a separate amplifier. If you have a small cabin to work with, the BAB8 will provide the rich bass that every sound system cannot do without.
Remote Subwoofer Control
A wired remote subwoofer control at your fingertips gives you control, so when the need hits… so does your BASS
One 10" Woofer with DUAL 4 ohm Voice Coil
2100 Watts MAX 1050 Watts RMS Power Handling
88dB Sensitivity, 34 Hz Resonant Frequency
Poly Injection Cone and Rubber Surround
Works in .65 CuFt Sealed or 1 CuFt Ported enclosure
50 Watts x 4 Max Power, Balance/Fader/Bass/Treble and Preset built-in EQ
Plays Bluetooth/CD/USB, MP3, WMA, FM/AM, Digital Media from Smart Phones
Compatible with Audio out from Smart Phones and MP3 Players
USB, Aux, Input
Front & Rear Pre Amp Outputs
Wireless Remote
Bluetooth Hands Free, Make and receive calls, Bluetooth Audio Streaming. Play and control music and apps like Spotify/Pandora wirelessly
Competition 6" pro audio speaker
The BDPRO6M-V9: BlackDeath 6 Inch Pro Audio Midrange component woofer is designed with excellent mid-bass response in mind. Semi-pressed paper cone has high sensitivity and low moving mass for monstrous output Dual roll cloth surround offers fast, precise dampening of the cone with great bass response. The BlackHole Dustcap increases effective cone area for higher SPL creating extreme volume.
Blackdeath range
VIBE Audio’s BlackDeath range is all about taking things to the extreme and creating products so crazy they have no right to exist. BlackDeath isn’t just about pushing the boundaries of audio innovation, it’s about annihilating them.
For many years people have been asking for coaxial and component speakers that are worthy to wear the BlackDeath logo, and after extensive development Vibe are proud to release the BlackDeath Pro Audio range. Derived from PA speaker design, BlackDeath Pro Audio speakers are capable of immense sound pressure levels, meaning volume like you’ve never heard before. Ideal for competition use or for those who just want to play their music loud and proud.
Specifications
Model : BlackDeath Pro 6M
Configuration : 1 Way
Speaker Size : 6″ (170mm)
RMS Power : 175 watts
Peak Power : 525 watts
Minimum Input : 75 watts
Sensitivity : 97 dB
Freq. Response : 75 Hz – 10 kHz
Impedance : 4 Ohm
Mounting Depth : 2.7″ (68mm)
Mounting Diameter: 5.7″ (146mm)
Voice Coil Diameter : 2″ (38mm)
Magnet Weight : 34 oz
Torsion basket featuring snap on mounting tabs for greater installation flexibility.
Sold as single speaker
Cone Made from polyurethane, the NX654 6. 5 inch car speakers provide a resilient and durable material that can offer great sound with the advantage of long lasting speakers
Voice Coil Our voice coils are able to withstand high temperatures yet maintain its strength and fatigue properties. This gives our speakers the advantage of longer play times with lower weights
Surround Rubber has the ability to endure much punishment without any sign of damage. It complements the whole structure of the speaker by allowing constant abuse where it is most needed, without the wear and tear
Basket A die cast frame can absorb and transfer much of the energy produced by the speaker. It has good corrosion resistance, good mechanical property, high thermal and electrical conductivity and retains strength at high temperatures
Tweeter The dome shape radiates sound with a wider dispersion pattern than the semi dome design. Since high frequency sound waves are very directional, a wider dispersion of the sound waves will give you a larger "sweet spot".Specs Impedance: 4 Ohms, Frequency: 65 Hz to 20 kHz, Dimensions: 7" x 7" x 3", Mounting Depth: 2. 3", Mounting hole: 5. 6". BOSS Audio Systems provides a powerful 3 year platinum online dealer so long as the purchase is made through . We strongly encourage professional installation of this product to ensure proper and safe functionality
Tweeter: Mylar Dome
Generally, the dome tweeter is a step up from the semi-dome tweeter, primarily because of improved sound dispersion. The dome shape radiates sound with a wider dispersion pattern than the semi-dome design. Since high-frequency sound waves are very directional, a wider dispersion of the sound waves will give you a larger 'sweet spot' to work with when setting up your system.
ONYX NX654
The classic style performance of the ONYX (NX) Series are a rare combination indeed. The custom designed poly injected cones and regimented linear travel provide an accuracy of sound production transporting the exact sonic experience the artist intended in the recording studio, directly into your vehicle.
Full Range 400 Watt 6.5” 4-way Speakers
Power Handling (peak): 200 Watts x 2
Dimensions: L 7” x W 7” x H 3”
Mounting depth: 2.25”
Impedance: 4 Ohms
Frequency Response: 65Hz – 20KHz
Sensitivity: 90 dB @ 1 W/1 m
Voice Coil: 1” Aluminum
Basket Structure: Cast
Tweeter: .75” Mylar Dome
Cone: Poly Injection
Polyurethane is categorized as a Polymer. It is a resilient, flexible and a durable manufactured material that allows for maximum flexibility that produces great sounding speakers lasting you a long time.
Surround: Rubber
Impermeable to air, rubber has the ability to endure or resist exposure to the many types of weather fronts. Rubber has many different applications. We use it for the surrounds in a many of our speakers to connect the cone to the basket.
Voice Coil: High Temperature
Our speakers are capable of higher or elevated temperature strength and fatigue properties that will increase performance and efficiency of heavy duty play time through lower weight and higher operating temperatures.
50 Watts x 4 Max Power, Balance/Fader/Bass/Treble and Preset built-in EQ
Plays Bluetooth/CD, FM/AM, Digital Media from Smart Phones
Compatible with Audio out from Smart Phones and MP3 Players
Reviews
There are no reviews yet.