Description |
- SLICKCBR12-V7: 12″ High Output Bass Enclosure Enclosure
- Designed to work with Powerbox 400.1M
- Unique port design for extended low frequency response
| Chaos Exxtreme 6" x 9" 2-Way 350W Full Range Speakers. (Sold in Pairs) | Phantom 6.5" 2-Way 500W Component Speakers. (Sold in Pairs) | Boss Audio System Phantom - 12" DUAL Voice Coil (4 Ohm) 2600W Subwoofer. (Sold Single) P129DC | Phantom - 10" DUAL Voice Coil (4 Ohm) 2100W Subwoofer. (Sold Single) | BOSS Audio Systems BAB8 Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space |
Content | SLICKCBR12-V7: Hybrid Ported Vented Bass Enclosure with 12 inch Subwoofer
The new Vibe Slick CBR (SLICKCBR12-V7) enclosure takes the radical approach of removing the integrated amplifier and replacing it with a separate unit, this gives several advantages. The enclosure design can now be focused only on the volume needed for the woofer rather than losing space to an internal power source. Using a separate amplifier means that sound quality is at the forefront. Vibe has developed an inline Powerbox Micro amplifier and ISOAWK kit (available separately) that can be purchased with the enclosure to make it compatible with an ISO T harness to plug into the existing stereo loom in the vehicle. this supplies audio signal and power and earth meaning there is no need to connect a separate cable through to the vehicles battery, just plug and play.
Specifications
- 1200w Peak
- 400w RMS
- Impedance 2 ohm
- 3.9″ x 21.6″ x 16.7″ (354 x 550 x 425mm)
- 4th order bass reflex enclosure
|
- Full Range 6" x 9" 2-Way Speaker Pair
- 350 Watts MAX 175 Watts RMS Power Handling per Pair
- 50 Hz to 20 kHz Frequency Response and 92dB Sensitivity
- Poly Injection Woofer Cone and Rubber Surround
- 1 Tweeter Per Speaker
- Sold in Pairs
|
- Component 6.5" 2-Way Speaker Pair
- 500 Watts MAX 250 Watts RMS Power Handling per Pair
- 65 Hz to 20 kHz Frequency Response and 94dB Sensitivity
- Electroplate Injection Woofer Cone and Rubber Surround
- 1 Tweeter Per Speaker
- Sold in Pairs
|
- One 12" Woofer with DUAL 4 ohm Voice Coil
- 2600 Watts MAX 1300 Watts RMS Power Handling
- 88dB Sensitivity, 28 Hz Resonant Frequency
- Polypropylene & Paper Cone and Rubber Surround
- Works in .65 CuFt Sealed or 1.5 CuFt Ported enclosure
|
- One 10" Woofer with DUAL 4 ohm Voice Coil
- 2100 Watts MAX 1050 Watts RMS Power Handling
- 88dB Sensitivity, 34 Hz Resonant Frequency
- Poly Injection Cone and Rubber Surround
- Works in .65 CuFt Sealed or 1 CuFt Ported enclosure
|
BOSS Audio Systems BAB8 Amplified Car Subwoofer
- Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
- Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
- Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
- Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
- High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
- Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
- Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.
|
Reviews
There are no reviews yet.